____________________________________________________________________________ | Property | WQ150 | WQ170 | WQ200 | WQ275 | WQ350 | |_____________________|__________|__________|__________|__________|__________| | Mass Per Unit | | | | | | | g/m2 (oz/yd2) | 150(4.2) | 170(4.5) | 200(6) | 275(8) | 350(10) | |_____________________|__________|__________|__________|__________|__________| | Structure | NW | NW | NW | NW | NW | |_____________________|__________|__________|__________|__________|__________| | Polymer | | | | | | | Composition | PET | PET | PET | PET | PET | |_____________________|__________|__________|__________|__________|__________| | % Open Area | | | | | | | CWO-22125 | NA | NA | NA | NA | NA | |_____________________|__________|__________|__________|__________|__________| | AOS | | | | | | | ASTM D4491-87 | | | | | | | mm (U.S. Seive) | 70 | 70 | 70 | 70 | 100 | |_____________________|__________|__________|__________|__________|__________| | Permittivity | | | | | | | ASTM D4491-92 | | | | | | | sec-1/Flow Rate | | | | | | |l/min/m2(gal/min/ft2)| 1.70(105)| 1.65(100)| 1.44(90) | 1.26(80) | 1.44(75) | |_____________________|__________|__________|__________|__________|__________| | Puncture | | | | | | | ASTM D 4833-88 | | | | | | | kN (lb) | (65) | (70) | (75) | (85) | (105) | |_____________________|__________|__________|__________|__________|__________| | Mullen Burst | | | | | | | ASTM D 3786-87 | | | | | | | kPa (psi) | (175) | (200) | (235) | (305) | (385) | |_____________________|__________|__________|__________|__________|__________| | Trapezoid | | | | | | | Tear Strength | | | | | | | ASTM D 4533-91 | | | | | | | kN (lb) | (55) | (60) | (70) | (80) | (90) | |_____________________|__________|__________|__________|__________|__________| | Grab/Tensile | | | | | | | Elongation | | | | | | | ASTM D 4632-91 | | | | | | | kN (lb)% | 85 | 85 | 85 | 85 | 85 | |_____________________|__________|__________|__________|__________|__________| | Wide With | | | | | | | Tensile Elongation | | | | | | | ASTM D 4595-86 | | | | | | | kN/m (lb/in) | | | | | | | MD | (35) | (40) | (45) | (60) | (85) | | XD | NP | NP | NP | NP | NP | |_____________________|__________|__________|__________|__________|__________| | Manufacturer's | | | | | | | Suggested | F,A/O | F,A/O | F,D,S/S, | F,D,S/S, | F,R,P, | | Applications | | | E | E | S/S,E | |_____________________|__________|__________|__________|__________|__________|
____________________________________________________________________________ | Property | WQ400 | WQ475 | WQ550 | PN040 | PN060 | |_____________________|__________|__________|__________|__________|__________| | Mass Per Unit | | | | | | | g/m2 (oz/yd2) | 400(12) | 475(14) | 550(16) | 135(4) | 200(6) | |_____________________|__________|__________|__________|__________|__________| | Structure | NW | NW | NW | NW | NW | |_____________________|__________|__________|__________|__________|__________| | Polymer | | | | | | | Composition | PET | PET | PET | PP | PP | |_____________________|__________|__________|__________|__________|__________| | % Open Area | | | | | | | CWO-22125 | NA | NA | NA | NA | NA | |_____________________|__________|__________|__________|__________|__________| | AOS | | | | | | | ASTM D4491-87 | | | | | | | mm (U.S. Seive) | 100 | 100 | 100 | 70 | 70 | |_____________________|__________|__________|__________|__________|__________| | Permittivity | | | | | | | ASTM D4491-92 | | | | | | | sec-1/Flow Rate | | | | | | |l/min/m2(gal/min/ft2)| 1.04(70) | 0.97(65) | 0.90(60) | 2.0(170) | 1.8(150) | |_____________________|__________|__________|__________|__________|__________| | Puncture | | | | | | | ASTM D 4833-88 | | | | | | | kN (lb) | (130) | (165) | (200) | (70) | (90) | |_____________________|__________|__________|__________|__________|__________| | Mullen Burst | | | | | || | ASTM D 3786-87 | | | | | | | kPa (psi) | (425) | (525) | (590) | (230) | (325) | |_____________________|__________|__________|__________|__________|__________| | Trapezoid | | | | | | | Tear Strength | | | | | | | ASTM D 4533-91 | | | | | | | kN (lb) | (110) | (120) | (135) | (50) | (65) | |_____________________|__________|__________|__________|__________|__________| | Grab/Tensile | | | | | | | Elongation | | | | | | | ASTM D 4632-91 | | | | | | | kN (lb)% | 85 | 85 | 85 | 50 | 50 | |_____________________|__________|__________|__________|__________|__________| | Wide With | | | | | | | Tensile Elongation | | | | | | | ASTM D 4595-86 | | | | | | | kN/m (lb/in) | | | | | | | MD | (120) | (155) | (185) | (60) | (75) | | XD | NP | NP | NP | NP | NP | |_____________________|__________|__________|__________|__________|__________| | Manufacturer's | | | | | | | Suggested | R,P,S/S, | R,P,S/S | R,P,S/S | F | F,D,S/S | | Applications | E | | | | E | |_____________________|__________|__________|__________|__________|__________|
____________________________________________________________________________ | Property | PN080 | PN100 | PN120 | PN140 | PN160 | |_____________________|__________|__________|__________|__________|__________| | Mass Per Unit | | | | | | | g/m2 (oz/yd2) | 275(8) | 350(10) | 400(12) | 475(14) | 550(16) | |_____________________|__________|__________|__________|__________|__________| | Structure | NW | NW | NW | NW | NW | |_____________________|__________|__________|__________|__________|__________| | Polymer | | | | | | | Composition | PP | PP | PP | PP | PP | |_____________________|__________|__________|__________|__________|__________| | % Open Area | | | | | | | CWO-22125 | NA | NA | NA | NA | NA | |_____________________|__________|__________|__________|__________|__________| | AOS | | | | | | | ASTM D4491-87 | | | | | | | mm (U.S. Seive) | 70 | 100 | 100 | 100 | 100 | |_____________________|__________|__________|__________|__________|__________| | Permittivity | | | | | | | ASTM D4491-92 | | | | | | | sec-1/Flow Rate | | | | | | |l/min/m2(gal/min/ft2)| 1.5(140) | 1.1(110) | 0.9(80) | 0.7(70) | 0.5(50) | |_____________________|__________|__________|__________|__________|__________| | Puncture | | | | | | | ASTM D 4833-88 | | | | | | | kN (lb) | | | | | | | | (120) | (150) | (175) | (210) | (230) | |_____________________|__________|__________|__________|__________|__________| | Mullen Burst | | | | | | | ASTM D 3786-87 | | | | | | | kPa (psi) | (400) | (500) | (600) | (660) | (770) | |_____________________|__________|__________|__________|__________|__________| | Trapezoid | | | | | | | Tear Strength | | | | | | | ASTM D 4533-91 | | | | | | | kN (lb) | (80) | (105) | (130) | (145) | (160) | |_____________________|__________|__________|__________|__________|__________| | Grab/Tensile | | | | | | | Elongation | | | | | | | ASTM D 4632-91 | | | | | | | kN (lb)% | 50 | 50 | 50 | 50 | 50 | |_____________________|__________|__________|__________|__________|__________| | Wide With | | | | | | | Tensile Elongation | | | | | | | ASTM D 4595-86 | | | | | | | kN/m (lb/in) | | | | | | | MD | (100) | (125) | (150) | (175) | (200) | | XD | NP | NP | NP | NP | NP | |_____________________|__________|__________|__________|__________|__________| | Manufacturer's | | | | | | | Suggested | F,D,S/S, | F,R,S/S | R,S/S,E, | R,S/S,P | R,S/S,P | | Applications | E | E,P | P | | | |_____________________|__________|__________|__________|__________|__________|