___________________________________________________________________________ |Property |901SC | 910SC |913SC |914SC |994 | |___________________|__________|__________|___________|__________|__________| |Mass Per Unit | | | | | | |g/m2 (oz/yd2) |NA |NA | NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |Structure | W/S(e) | W/S(e) | W/S(e) | W/C(g) | W/S(e) | |___________________|__________|__________|___________|__________|__________| |Polymer | | | | | | |Composition | PP | PP |PP |PP |PP | |___________________|__________|__________|___________|__________|__________| |% Open Area | | | | | | |CWO-22125 | <1% |<1% |<1% |<4.4% |<1% | |___________________|__________|__________|___________|__________|__________| |AOS | | | | | | |ASTM D4491-87 | | | | | | |mm (U.S. Seive) |1.180(16) |0.850(20) |0.850(20) |0.600(30) |0.600(30) | |___________________|__________|__________|___________|__________|__________| |Permittivity | | | | | | |ASTM D4491-92 | | | | | | |sec-1/Flow Rate | | | | | | |l/min/m2 |0.70 |0.20 |0.05 |0.04 |0.07 | |(gal/min/ft2) |2037(50) |611(15)8) |122(3) |81(2) |244(6) | |___________________|__________|__________|___________|__________|__________| |Puncture | | | | | | |ASTM D 4833-88 | | | | | | |kN (lb) |0.11(25) |0.26(58) |0.16(35) |0.27(60) |0.31(70) | |___________________|__________|__________|___________|__________|__________| | | | | |Mullen Burst | | | | | | |ASTM D 3786-87 | | | | | | |kPa (psi) |1171(170) |1826(265) |1826(265) |2411(350) |1860(270) | |___________________|__________|__________|___________|__________|__________| |Trapezoid |0.20 x |0.22 x |0.22 x |0.27 x |0.22 x | |Tear Strength | 0.09 | 0.22 | 0.18 | 0.27 | 0.18 | |ASTM D 4533-91 |(45 x 20) |(50 x 50) |(50 x 40) |(60 x 60) |(50 x 40) | |kN (lb) | | | | | | |___________________|__________|__________|___________|__________|__________| |Grab/Tensile |0.38 x |0.45 x |0.67 x 0.45|0.62 x |0.89 x | |Elongation | 0.22 | 0.45 |(150 x | 0.42 | 0.89 | |ASTM D 4632-91 |(85 x 50)/|(100 x100)|100)/9 x 13|(140 x 95)|(200 x200)| |kN (lb)% |13 x 13 |/15 x 15 | |/15 x 15 |/15 x 15 | |___________________|__________|__________|___________|__________|__________| |Wide With | | | | | | |Tensile Elongation | | | | | | |ASTM D 4595-86 | | | | | | |kN/m (lb/in) | | | | | | |MD |NA |NA |NA |NA |NA | |XD |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |Manufacturer's | | | | | | |Suggested | | | | | | |Applications |S/F |S/F |S/F |S/F |S/F | |___________________|__________|__________|___________|__________|__________| S/S="Separation/Stabilization" D="Drainage" R="Reinforcement" P="Protection" F="Filtration" E="Erosion" Control A/O="Asphalt" Overlay S/F="Silt" Fence O/C="Other" or Combination NP="Not" provided by manufacturer PP="Polypropylene" PET="Polyester" PE="Polyethlene" (b) area of opening/total area determined (d) available w/wo drawstring from a light (f) woven monofilament (e) woven slit film function (g) woven combinationGeotextile Product Data - Synthetic Industries CONT
____________________________________________________________________________ |Property |200ST |300ST |400R |Erosion I |Erosion III| |___________________|__________|__________|___________|__________|___________| |Mass Per Unit | | | | | | |g/m2 (oz/yd2) |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|___________| |Structure |W/S(e) |W/S(e) |W/C(g) |W/M(f) |W/M(f) | |___________________|__________|__________|___________|__________|___________| |Polymer |PP |PP |PP |PP |PP | |Composition | | | | | | |___________________|__________|__________|___________|__________|___________| |% Open Area |<1% |<1% |<1% |4% |5% | |CWO-22125 | | | | | | |___________________|__________|__________|___________|__________|___________| |AOS | | | | | | |ASTM D4491-87 | | | | | | |mm (U.S. Seive) |0.600(30) |0.600(30) |0.600(30) |0.212(70) |0.425(40) | |___________________|__________|__________|___________|__________|___________| |Permittivity | | | | | | |ASTM D4491-92 | | | | | | |sec-1/Flow Rate | | | | | | |l/min/m2 | | | | | | |(gal/min/ft2) |244(6) |203(5) |1830(45) |732(18) |1220(30) | |___________________|__________|__________|___________|__________|___________| |Puncture | | | | | | |ASTM D 4833-88 | | | | | | |kN (lb) |0.45(100) |0.53(120) |0.62(140) |0.67(150) |0.62(140) | |___________________|__________|__________|___________|__________|___________| | | | | |Mullen Burst | | | | | | |ASTM D 3786-87 | | | | | | |kPa (psi) |3101(450) |4134(600) |8270(1200) |3307(480) |3548(515) | |___________________|__________|__________|___________|__________|___________| |Trapezoid | |0.53 x | |0.42 x |0.44 x | |Tear Strength |0.38 x | 0.53 |0.82 x 0.85| 0.42 | 0.27 | |ASTM D 4533-91 | 0.40 |(120 x |(185 x 190)|(95 x 55) |(100 x 60) | |kN (lb) |(85 x 90) | 120) | | | | |___________________|__________|__________|___________|__________|___________| |Grab/Tensile |0.89 x |1.33 x | |1.76 x |1.60 x | |Elongation | 0.89 | 1.33 | | 1.16 | 1.16 | |ASTM D 4632-91 |(200 x200)|(300x 300)| |(395 x260)|(360 x260) | |kN (lb)% |/15 x 15 |/15 x 15 |NA |/24 x 24 |/20 x 20 | |___________________|__________|__________|___________|__________|___________| |Wide With | | | | | | |Tensile Elongation | | | | | | |ASTM D 4595-86 | | | | | | |kN/m (lb/in) | | | | | | |MD |21.0(120 |30.6(175) |70.0(400) |NA |NA | |XD |21.0(120) |30.6(175) |70.0(400) |NA |NA | |___________________|__________|__________|___________|__________|___________| |Manufacturer's | | | | | | |Suggested | | | | | | |Applications |S/S,R,E |S/S,R,E |S/S,R |S/S,E,F,D |S/S,E,F,D | |___________________|__________|__________|___________|__________|___________| S/S="Separation/Stabilization" D="Drainage" R="Reinforcement" P="Protection" F="Filtration" E="Erosion" Control A/O="Asphalt" Overlay S/F="Silt" Fence O/C="Other" or Combination NP="Not" provided by manufacturer PP="Polypropylene" PET="Polyester" PE="Polyethlene" (b) area of opening/total area determined (d) available w/wo drawstring from a light (f) woven monofilament (e) woven slit film functionGeotextile Product Data - Synthetic Industries CONT
___________________________________________________________________________ |Property |Erosion V |Erosion X |Erosion XV |381 | 311 | |___________________|__________|__________|___________|__________|__________| |Mass Per Unit |NA |NA | NA |NA |NA | |g/m2 (oz/yd2) | | | | | | |___________________|__________|__________|___________|__________|__________| |Structure |W/M(f) |W/M(f) |W/M(f) |Nonwoven |Nonwoven | |___________________|__________|__________|___________|__________|__________| |Polymer | | | | | | |Composition |PP |PP |PP |PP |PP | |___________________|__________|__________|___________|__________|__________| |% Open Area | | | | | | |CWO-22125 |11% |17% |3% |NA |NA | |___________________|__________|__________|___________|__________|__________| |AOS | | | | | | |ASTM D4491-87 | | | | | | |mm (U.S. Seive) |0.600(30) |0.850(20) |0.425(40) |NA |NA | |___________________|__________|__________|___________|__________|__________| |Permittivity | | | | | | |ASTM D4491-92 | | | | | | |sec-1/Flow Rate | | | | | | |l/min/m2 |4475(110) |8136(200) |1630(40) |NA | 2 | |(gal/min/ft2) | | | | |4482(110) | |___________________|__________|__________|___________|__________|__________| |Puncture | | | | | | |ASTM D 4833-88 | | | | | | |kN (lb) |0.58(130) |0.60(135) |0.47(165) |0.27(60) |0.22(56) | |___________________|__________|__________|___________|__________|__________| | | | | |Mullen Burst | | | | | | |ASTM D 3786-87 | | | | | | |kPa (psi) |3548(5150)|2894(420) |5546(805) |1447(210) |1137(165) | |___________________|__________|__________|___________|__________|__________| |Trapezoid | | | | | | |Tear Strength |0.44 x |0.18 x |0.53 x 0.53| | | |ASTM D 4533-91 | 0.36 | 0.22|(120 x 120)| | | |kN (lb) |(100 x 80)|(40 x 50) | |0.18(40) |0.13(30) | |___________________|__________|__________|___________|__________|__________| |Grab/Tensile |1.60 x |1.13 x | | | | |Elongation | 1.16 | 1.22 |1.47 x 1.94| | | |ASTM D 4632-91 |(360 x260)|(255 x275)|(330 x 435)|0.40(90) |0.36(80) | |kN (lb)% |/27 x 15 |/20 x 15 |/15 x 20 |/50 | /45 | |___________________|__________|__________|___________|__________|__________| |Wide With | | | | | | |Tensile Elongation | | | | | | |ASTM D 4595-86 | | | | | | |kN/m (lb/in) | | | | | | |MD |NA |NA |28.0(160)/ |30.6(175)/|NA | | | | | 12 | 12 | | |XD |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |Manufacturer's | | | | | | |Suggested | | | | | | |Applications |S/S,E,F,D |E,F,D |E,F,D,S/S,R| A/O | F,D | |___________________|__________|__________|___________|__________|__________| S/S = Separation/Stabilization D = Drainage R = Reinforcement P = Protection F = Filtration E = Erosion Control A/O = Asphalt Overlay S/F = Silt Fence O/C = Other or Combination NP = Not provided by manufacturer PP = Polypropylene PET = Polyester PE = Polyethlene (b) area of opening/total area determined (d) available w/wo drawstring from a light (f) woven monofilament (e) woven slit film functionGeotextile Product Data - Synthetic Industries CONT
___________________________________________________________________________ |Property |351 |401 |451 |501 |601 | |___________________|__________|__________|___________|__________|__________| |Mass Per Unit | | | | | | |g/m2 (oz/yd2) |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |Structure |Nonwoven |Nonwoven |Nonwoven |Nonwoven |Nonwoven | |___________________|__________|__________|___________|__________|__________| |Polymer | | | | | | |Composition |PP |PP |PP |PP |PP | |___________________|__________|__________|___________|__________|__________| |% Open Area | | | | | | |CWO-22125 |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |AOS | | | | | | |ASTM D4491-87 | | | | | | |mm (U.S. Seive) |0.212(70) |0.212(70) |0.212(70) |0.212(70) |0.212(70) | |___________________|__________|__________|___________|__________|__________| |Permittivity | | | | | | |ASTM D4491-92 | | | | | | |sec-1/Flow Rate | | | | | | |l/min/m2 | 2 | 2 | 1.5 |1.4 |1.3 | |(gal/min/ft2) |4482(1100 |5704(140) |4889(120) |4686(115) |4482(110) | |___________________|__________|__________|___________|__________|__________| |Puncture | | | | | | |ASTM D 4833-88 | | | | | | |kN (lb) |0.24(55) |0.29(65) |0.31(70) |0.38(85) |0.42(95) | |___________________|__________|__________|___________|__________|__________| | | | | |Mullen | | | | | | |Burst | | | | | | |ASTM D 3786-87 | | | | | | |kPa (psi) |1275(185) |1550(225) |1654(240) |1894(275) |2239(325) | |___________________|__________|__________|___________|__________|__________| |Trapezoid | | | | | | |Tear Strength | | | | | | |ASTM D 4533-91 | | | | | | |kN (lb) |0.16(35) |0.2(45) |0.22(50) |0.25(57) |0.27(60) | |___________________|__________|__________|___________|__________|__________| |Grab/Tensile | | | | | | |Elongation | | | | | | |ASTM D 4632-91 |0.4(90)/50|0.44(100) |0.53(120) |0.60(135) |0.67(150) | |kN (lb)% | | /50 | /50 | /50 | /50 | |___________________|__________|__________|___________|__________|__________| |Wide With | | | | | | |Tensile Elongation | | | | | | |ASTM D 4595-86 | | | | | | |kN/m (lb/in) | | | | | | |MD |NA |NA |NA |NA |NA | |XD |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |Manufacturer's | | | | | | |Suggested | | | | | | |Applications |F,D,E | F,D,E |F,D,E |F,D,E,S/S |F,D,E,S/S | |___________________|__________|__________|___________|__________|__________| S/S = Separation/Stabilization D = Drainage R = Reinforcement P = Protection F = Filtration E = Erosion Control A/O = Asphalt Overlay S/F = Silt Fence O/C = Other or Combination NP = Not provided by manufacturer PP = Polypropylene PET = Polyester PE = Polyethlene (b) area of opening/total area determined (d) available w/wo drawstring from a light (f) woven monofilament (e) woven slit film functionGeotextile Product Data - Synthetic Industries CONT
___________________________________________________________________________ |Property |701 | 801 |1001 |1201 |1601 | |___________________|__________|__________|___________|__________|__________| |Mass Per Unit | | | | | | |g/m2 (oz/yd2) |NA |NA | NA | NA |NA | |___________________|__________|__________|___________|__________|__________| |Structure |Nonwoven |Nonwoven |Nonwoven |Nonwoven |Nonwoven | |___________________|__________|__________|___________|__________|__________| |Polymer | | | | | | |Composition |PP |PP |PP |PP |PP | |___________________|__________|__________|___________|__________|__________| |% Open Area | | | | | | |CWO-22125 |NA | NA |NA |NA | NA | |___________________|__________|__________|___________|__________|__________| |AOS | | | | | | |ASTM D4491-87 | | | | | | |mm (U.S. Seive) |0.212(70) |0.18(80) |0.15(100) |0.15(100) |0.15(100) | |___________________|__________|__________|___________|__________|__________| |Permittivity | | | | | | |ASTM D4491-92 | | | | | | |sec-1/Flow Rate | | | | | | |l/min/m2 |1.5 |1.5 |1.2 |1.0 |0.7 | |(gal/min/ft2) |4482(110) |4482(110) |3463(85) |3056 |2037(50) | |___________________|__________|__________|___________|__________|__________| |Puncture | | | | | | |ASTM D 4833-88 | | | | | | |kN (lb) |0.49(110) |0.56(130) |0.71(160) |0.8(180) |1.07(240) | |___________________|__________|__________|___________|__________|__________| | | | | |Mullen Burst | | | | | | |ASTM D 3786-87 | | | | | | |kPa (psi) |2411(350) |2756(400) |3514(510) |4134(600) |5512(800) | |___________________|__________|__________|___________|__________|__________| |Trapezoid | | | | | | |Tear Strength | | | | | | |ASTM D 4533-91 | | | | | | |kN (lb) |0.33(75) |0.38(85) |0.44(100) |0.51(115) |0.64(145) | |___________________|__________|__________|___________|__________|__________| |Grab/Tensile | | | | | | |Elongation | | | | | | |ASTM D 4632-91 |0.8(180) |0.89(200) |1.11(350) |1.33(300) |1.69(380) | |kN (lb)% | /50 | /50 | /50 | /50 | /50 | |___________________|__________|__________|___________|__________|__________| |Wide With | | | | | | |Tensile Elongation | | | | | | |ASTM D 4595-86 | | | | | | |kN/m (lb/in) | | | | | | |MD |NA |NA |NA |NA |NA | |XD |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |Manufacturer's | | | | | | |Suggested | | | | | | |Applications |F,D,E,S/S |F,D,E,S/S |F,D,E,S/S |F,D,P,S/S |F,D,P,S/S | |___________________|__________|__________|___________|__________|__________| S/S = Separation/Stabilization D = Drainage R = Reinforcement P = Protection F = Filtration E = Erosion Control A/O = Asphalt Overlay S/F = Silt Fence O/C = Other or Combination NP = Not provided by manufacturer PP = Polypropylene PET = Polyester PE = Polyethlene (b) area of opening/total area determined (d) available w/wo drawstring from a light (f) woven monofilament (e) woven slit film function