___________________________________________________________________________ |Property |Nicolon |Nicolon |Nicolon |Stabilenka|Stabilenka| | |HS600 |HS1150 |HS1715 | 2400 | 3000 | |___________________|__________|__________|___________|__________|__________| |Mass Per Unit |NA |NA |NA |NA |NA | |g/m2 (oz/yd2) | | | | | | |___________________|__________|__________|___________|__________|__________| |Structure |Woven |Woven |Woven |Woven |Woven | |___________________|__________|__________|___________|__________|__________| |Polymer | | | | | | |Composition |PET |PET |PET |PET |PET | |___________________|__________|__________|___________|__________|__________| |% Open Area | | | | | | |CWO-22125 |NA | NA | NA | NA |NA | |___________________|__________|__________|___________|__________|__________| |AOS | | | | | | |ASTM D4491-87 | | | | | | |mm (U.S. Seive) |0.85(20) |0.59(30) |0.59(30) |NA |NA | |___________________|__________|__________|___________|__________|__________| |Permittivity | | | | | | |ASTM D4491-92 | | | | | | |sec-1/Flow Rate | | | | | | |l/min/m2 |0.32 |0.84 |0.65 |NA |NA | |(gal/min/ft2) |1019(25) |2648(65) |2037(50) | | | |___________________|__________|__________|___________|__________|__________| |Puncture | | | | | | |ASTM D 4833-88 | | | | | | |kN (lb) |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |Mullen | | | | | | |Burst | | | | | | |ASTM D 3786-87 | | | | | | |kPa (psi) |NA |NA | NA | NA |NA | |___________________|__________|__________|___________|__________|__________| |Trapezoid | | | | | | |Tear Strength | | | | | | |ASTM D 4533-91 | | | | | | |kN (lb) |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |Grab/Tensile | | | | | | |Elongation | | | | | | |ASTM D 4632-91 | | | | | | |kN (lb)% |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |Wide With | | | | | | |Tensile Elongation | | | | | | |ASTM D 4595-86 | | | | | | |kN/m (lb/in) | | | | | | |MD |105(600) |201(1150) |298(1700) |420(2400) |526(3000) | |XD |88(500) |123(700) |123(700) |123(700) |123(700) | |___________________|__________|__________|___________|__________|__________| |Manufacturer's | | | | | | |Suggested | | | | | | |Applications |R |R |R |R |R | |___________________|__________|__________|___________|__________|__________| S/S = Separation/Stabilization D = Drainage R = Reinforcement P = Protection F = Filtration E = Erosion Control A/O = Asphalt Overlay S/F = Silt Fence O/C = Other or Combination NP = Not provided by manufacturer PP = Polypropylene PET = Polyester PE = Polyethylene
___________________________________________________________________________ |Property |Stabilenka|Nicolon |Nicolon |Nicolon |Nicolon | | |3600 |S400 |S600 |S700 |S800 | |___________________|__________|__________|___________|__________|__________| |Mass Per Unit | | | | | | |g/m2 (oz/yd2) |NA |4.0 |6.0 |7.0 |8.0 | |___________________|__________|__________|___________|__________|__________| |Structure |Woven |Nonwoven |Nonwoven |Nonwoven |Nonwoven | |___________________|__________|__________|___________|__________|__________| |Polymer | | | | | | |Composition |PET |PP |PP |PP |PP | |___________________|__________|__________|___________|__________|__________| |% Open Area | | | | | | |CWO-22125 |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |AOS | | | | | | |ASTM D4491-87 | | | | | | |mm (U.S. Seive) |NA |0.212(70) |0.212(70) |0.212(70) |0.212(70) | |___________________|__________|__________|___________|__________|__________| |Permittivity | | | | | | |ASTM D4491-92 | | | | | | |sec-1/Flow Rate | | | | | | |l/min/m2 | |2.28 |1.63 |1.41 |1.26 | |(gal/min/ft2) |NA |7333(180) |(5296(130) |4481(110) |4074(100) | |___________________|__________|__________|___________|__________|__________| |Puncture | | | | | | |ASTM D 4833-88 | | | | | | |kN (lb) |NA |0.289(65) |0.422(95) |0.511(115)|0.58(130) | |___________________|__________|__________|___________|__________|__________| |Mullen | | | | | | |Burst | | | | | | |ASTM D 3786-87 | | | | | | |kPa (psi) |NA |1585(230) |2412(350) |2756(400) |3101(450) | |___________________|__________|__________|___________|__________|__________| |Trapezoid | | | | | | |Tear Strength | | | | | | |ASTM D 4533-91 | | | | | | |kN (lb) |NA |0.200(45) |0.29(65) |0.356(80) |0.4(90) | |___________________|__________|__________|___________|__________|__________| |Grab/Tensile | | | | | | |Elongation | | | | | | |ASTM D 4632-91 | |0.467 |0.712 |0.89 |1.001 | |kN (lb)% |NA |(105)/60 |(160)/50 |(200)/50 |(225)/50 | |___________________|__________|__________|___________|__________|__________| |Wide With | | | | | | |Tensile Elongation | | | | | | |ASTM D 4595-86 | | | | | | |kN/m (lb/in) | | | | | | |MD |631(3600) |NA |NA |NA |NA | |XD |123(700) |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |Manufacturer's | | | | | | |Suggested | | | | |R,P,D,F, | |Applications |R |F,D,E |S/S,D,E |S/S,D,E |S/S | |___________________|__________|__________|___________|__________|__________| S/S = Separation/Stabilization D = Drainage R = Reinforcement P = Protection F = Filtration E = Erosion Control A/O = Asphalt Overlay S/F = Silt Fence O/C = Other or Combination NP = Not provided by manufacturer PP = Polypropylene PET = Polyester PE = Polyethylene
___________________________________________________________________________ |Property |Nicolon |Nicolon |Nicolon |Nicolon |Mirafi | | |S1000 |S1200 |S1400 |S1600 |100X | |___________________|__________|__________|___________|__________|__________| |Mass Per Unit | | | | | | |g/m2 (oz/yd2) |(10) |(12) |(14) |(16) |NA | |___________________|__________|__________|___________|__________|__________| |Structure |Nonwoven |Nonwoven |Nonwoven |Nonwoven |Woven | |___________________|__________|__________|___________|__________|__________| |Polymer | | | | | | |Composition |PP |PP |PP |PP |PP | |___________________|__________|__________|___________|__________|__________| |% Open Area | | | | | | |CWO-22125 |NA |NA |NA |N |1 | |___________________|__________|__________|___________|__________|__________| |AOS | | | | | | |ASTM D4491-87 | | | | | | |mm (U.S. Seive) |0.15(100) |0.15(100) |0.15(100) |0.15(100) |0.841(20) | |___________________|__________|__________|___________|__________|__________| |Permittivity | | | | | | |ASTM D4491-92 | | | | | | |sec-1/Flow Rate | | | | | | |l/min/m2 |0.936 |0.751 |0.642 |0.571 |0.2 | |(gal/min/ft2) |3056(75) |2444(60) |2037(50) |1833(45) |815(20) | |___________________|__________|__________|___________|__________|__________| |Puncture | | | | | | |ASTM D 4833-88 | | | | | | |kN (lb) |0.73(165) |0.85(190) |0.98(220) |1.07(240) |0.27(60) | |___________________|__________|__________|___________|__________|__________| |Mullen | | | | | | |Burst | | | | | | |ASTM D 3786-87 | | | | | | |kPa (psi) |3858(560) |4479(650) |4495(725) |5512(800) |2067(300) | |___________________|__________|__________|___________|__________|__________| |Trapezoid | | | | | | |Tear Strength | | | | | | |ASTM D 4533-91 | | | | | | |kN (lb) |0.47(105) |0.58(130) |0.62(140) |0.69(155) |0.27(60) | |___________________|__________|__________|___________|__________|__________| |Grab/Tensile | | | | |0.53 x | |Elongation | | | | |0.45/10 | |ASTM D 4632-91 |1.246 |1.6(360) |1.89 |2.225 |(120 x | |kN (lb)% |(280)/50 | /60 |(425)/60 |(500)/60 | 100)/10 | |___________________|__________|__________|___________|__________|__________| |Wide With | | | | | | |Tensile Elongation | | | | | | |ASTM D 4595-86 | | | | | | |kN/m (lb/in) | | | | | | |MD |NA |NA |NA |NA |NA | |XD |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |Manufacturer's | | | | | | |Suggested |R,P,D,F, |R,P,S/S |R,P,S/S |R,P,S/S |NP | |Applications | S/S | | | | | |___________________|__________|__________|___________|__________|__________| S/S = Separation/Stabilization D = Drainage R = Reinforcement P = Protection F = Filtration E = Erosion Control A/O = Asphalt Overlay S/F = Silt Fence O/C = Other or Combination NP = Not provided by manufacturer PP = Polypropylene PET = Polyester PE = Polyethylene
___________________________________________________________________________ |Property |Mirafi |Mirafi |Mirafi |Mirafi |Mirafi | | |500XL |500X |600X |700X |700XG | |___________________|__________|__________|___________|__________|__________| |Mass Per Unit | | | | | | |g/m2 (oz/yd2) |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |Structure |Woven |Woven |Woven |Woven |Woven | |___________________|__________|__________|___________|__________|__________| |Polymer | | | | | | |Composition |PP |PP |PP |PP |PP | |___________________|__________|__________|___________|__________|__________| |% Open Area | | | | | | |CWO-22125 | 1 | 1 | 1 | 4 | 10 | |___________________|__________|__________|___________|__________|__________| |AOS | | | | | | |ASTM D4491-87 | | | | | | |mm (U.S. Seive) |0.595(30) |0.595(30) |0.420(40) |0.210(70) |0.420(40) | |___________________|__________|__________|___________|__________|__________| |Permittivity | | | | | | |ASTM D4491-92 | | | | | | |sec-1/Flow Rate | | | | | | |l/min/m2 |0.04 |0.03 |0.02 |0.28 |1.36 | |(gal/min/ft2) |163(4) |163(4) |81(2) |733(18) |4074(100) | |___________________|__________|__________|___________|__________|__________| |Puncture | | | | | | |ASTM D 4833-88 | | | | | | |kN (lb) |0.31(70) |0.40(90) |0.53(120) |0.60(135) |0.51(115) | |___________________|__________|__________|___________|__________|__________| |Mullen | | | | | | |Burst | | | | | | |ASTM D 3786-87 | | | | | | |kPa (psi) |2412(350) |2756(400) |4134(600) |3307(480) |3445(500) | |___________________|__________|__________|___________|__________|__________| |Trapezoid | | | | | | |Tear Strength | | | |0.45 x |0.51 x | |ASTM D 4533-91 | | | |0.27 | 0.33| |kN (lb) |0.20(45) |0.33(75) |0.53(120) |(100 x 60)|(115 x 75)| |___________________|__________|__________|___________|__________|__________| |Grab/Tensile | |0.89 x |1.34 x |1.65 x |1.62 x | |Elongation | |0.89/15 | 1.11/15 |1.11/15 | 0.89/10 | |ASTM D 4632-91 |0.62 |(200 x |(300 x |(370 x |(365 x | |kN (lb)% |(140)/15 | 200)/15 | 300)/15) | 250/15) | 200/10) | |___________________|__________|__________|___________|__________|__________| |Wide With | | | | | | |Tensile Elongation | | | | | | |ASTM D 4595-86 | | | | | | |kN/m (lb/in) | | | | | | |MD |NA |18(100) |29(165) |39(225) |35(200) | |XD |NA |21(120) |31(175) |25(145) |24(135) | |___________________|__________|__________|___________|__________|__________| |Manufacturer's | | | | | | |Suggested |NP |NP |NP |NP |NP | |Applications | | | | | | |___________________|__________|__________|___________|__________|__________| S/S = Separation/Stabilization D = Drainage R = Reinforcement P = Protection F = Filtration E = Erosion Control A/O = Asphalt Overlay S/F = Silt Fence O/C = Other or Combination NP = Not provided by manufacturer PP = Polypropylene PET = Polyester PE = Polyethylene
____________________________________________________________________________ |Property |Filterweave|Filterweave|Filterweave|Mirafi |Nicolon | | |70/20 |40/10 |40/30A |HP800X |HP500 | |___________________|___________|___________|___________|_________|__________| |Mass Per Unit | | | | | | |g/m2 (oz/yd2) |NA |NA |NA |NA |NA | |___________________|___________|___________|___________|_________|__________| |Structure |Woven |Woven |Woven |Woven |Woven | |___________________|___________|___________|___________|_________|__________| |Polymer | | | | | | |Composition |PP |PP |PP |PP |PP | |___________________|___________|___________|___________|_________|__________| |% Open Area | | | | | | |CWO-22125 |10 | 10 | 20 | 1 | 8 | |___________________|___________|___________|___________|_________|__________| |AOS | | | | | | |ASTM D4491-87 | | | | | | |mm (U.S. Seive) |0.250(60) |0.420(40) |0.420(40) |0.210(70)|0.595(30) | |___________________|___________|___________|___________|_________|__________| |Permittivity | | | | | | |ASTM D4491-92 | | | | | | |sec-1/Flow Rate | | | | | | |l/min/m2 |0.506 |0.95 |2.14 |0.1 |1.5 | |(gal/min/ft2) |1426(35) |2852(70) |5907(145) |326(8) |4685(115) | |___________________|___________|___________|___________|_________|__________| |Puncture | | | | | | |ASTM D 4833-88 | | | | | | |kN (lb) |0.65(145) |0.56(125) |0.51(115) |0.80(180)|0.65(145) | |___________________|___________|___________|___________|_________|__________| |Mullen | | | | | | |Burst | | | | | | |ASTM D 3786-87 | | | | | | |kPa (psi) |4065(590) |3445(500) |2756(400) |4823(700)|4995(725) | |___________________|___________|___________|___________|_________|__________| |Trapezoid | | | |0.53 x |0.65 x | |Tear Strength | | | | 0.62 | 0.56 | |ASTM D 4533-91 |0.47 x 0.62|0.36 x 0.31|0.40 x 0.22|(120 x |(145 x | |kN (lb) |(105 x 140)|(80 x 70) |(90 x 50) | 140) | 125) | |___________________|___________|___________|___________|_________|__________| |Grab/Tensile |1.22 x 1.74|1.18 x 1.13|1.45 x 0.89|1.49 x |1.78 x | |Elongation | /15 | /15 | /15 |1.89/17 |1.49/15 | |ASTM D 4632-91 |(275 x 390/|(265 x 255/|(325 x 200/|(335 x |(400 x | |kN (lb)% | 15) | 15)| 15) |425/17) |335/15) | |___________________|___________|___________|___________|_________|__________| |Wide With | | | | | | |Tensile Elongation | | | | | | |ASTM D 4595-86 | | | | | | |kN/m (lb/in) | | | | | | |MD |31.5(180) |26(150) |31(175) |NA |40(230) | |XD |32(185) |29(165) |19(110) |NA |39(225) | |___________________|___________|___________|___________|_________|__________| |Manufacturer's | | | | | | |Suggested | | | | | | |Applications |NP |NP |NP |NP |NP | |___________________|___________|___________|___________|_________|__________| S/S = Separation/Stabilization D = Drainage R = Reinforcement P = Protection F = Filtration E = Erosion Control A/O = Asphalt Overlay S/F = Silt Fence O/C = Other or Combination NP = Not provided by manufacturer PP = Polypropylene PET = Polyester PE = Polyethylene
___________________________________________________________________________ |Property |Nicolon |Nicolon |Nicolon |Mirafi |Mirafi | | |HP550 |565 |HP570 |14ONL |14ONC | |___________________|__________|__________|___________|__________|__________| |Mass Per Unit | | | | | | |g/m2 (oz/yd2) |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |Structure |Woven |Woven |Woven |Nonwoven |Nonwoven | |___________________|__________|__________|___________|__________|__________| |Polymer | | | | | | |Composition |PP |PP |PP |PP |PP | |___________________|__________|__________|___________|__________|__________| |% Open Area | | | | | | |CWO-22125 | 6 | NA | NA | NA | NA | |___________________|__________|__________|___________|__________|__________| |AOS | | | | | | |ASTM D4491-87 | | | | | | |mm (U.S. Seive) |0.420(40) |0.420(40) |0.595(30) |0.210(70) |0.210(70) | |___________________|__________|__________|___________|__________|__________| |Permittivity | | | | | | |ASTM D4491-92 | | | | | | |sec-1/Flow Rate | | | | | | |l/min/m2 |0.96 |0.07 |0.4 |2.0 |1.5 | |(gal/min/ft2) |2852(70) |204(5) |1222(30) |4481(110) |4889(120) | |___________________|__________|__________|___________|__________|__________| |Puncture | | | | | | |ASTM D 4833-88 | | | | | | |kN (lb) |0.73(165) |0.89(200) |0.71(160) |0.24(55) |0.31(70) | |___________________|__________|__________|___________|__________|__________| |Mullen | | | | | | |Burst | | | | | | |ASTM D 3786-87 | | | | | | |kPa (psi) |4789(695) |8268(1200)|8268(1200) |1275(185) |1654(240) | |___________________|__________|__________|___________|__________|__________| |Trapezoid |0.65 x |0.78 x | | | | |Tear Strength | 0.56 | 0.96 | | | | |ASTM D 4533-91 |(145 x |(175 x |0.80 x 0.80|0.16 |0.22 | |kN (lb) | 125) | 125) |(180 x 180)|(35) |(50) | |___________________|__________|__________|___________|__________|__________| |Grab/Tensile |1.89 x |2.23 x |1.85 x 1.82| |0.49 x | |Elongation |1.56/21 |2.23/10 | /8 | | 0.58/50 | |ASTM D 4632-91 |(425 x 350|(500 x 500|(415 x 410/|0.40 |(110 x | |kN (lb)% | /21) | /10) | 8) |(90)/15 | 130/50) | |___________________|__________|__________|___________|__________|__________| |Wide With | | | | | | |Tensile Elongation | | | | | | |ASTM D 4595-86 | | | | | | |kN/m (lb/in) | | | | | | |MD |47(270) |61(350) |70(400) |NA |NA | |XD |39(225) |66(375) |70(400) |NA |NA | |___________________|__________|__________|___________|__________|__________| |Manufacturer's | | | | | | |Suggested | | | | | | |Applications |NP |NP |NP |NP |NP | |___________________|__________|__________|___________|__________|__________| S/S = Separation/Stabilization D = Drainage R = Reinforcement P = Protection F = Filtration E = Erosion Control A/O = Asphalt Overlay S/F = Silt Fence O/C = Other or Combination NP = Not provided by manufacturer PP = Polypropylene PET = Polyester PE = Polyethylene
___________________________________________________________________________ |Property |Mirafi |Mirafi |Mirafi |Mirafi |Mirafi | | |140N |160N |180N |1100N |1120N | |___________________|__________|__________|___________|__________|__________| |Mass Per Unit | | | | | | |g/m2 (oz/yd2) |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |Structure |Nonwoven |Nonwoven |Nonwoven |Nonwoven |Nonwoven | |___________________|__________|__________|___________|__________|__________| |Polymer | | | | | | |Composition |PP |Nonwoven |Nonwoven |PP |PP | |___________________|__________|__________|___________|__________|__________| |% Open Area | | | | | | |CWO-22125 |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |AOS | | | | | | |ASTM D4491-87 | | | | | | |mm (U.S. Seive) |0.210(70) |0.210(70) |0.177(80) |0.149(100)|0.149(100)| |___________________|__________|__________|___________|__________|__________| |Permittivity | | | | | | |ASTM D4491-92 | | | | | | |sec-1/Flow Rate | | | | | | |l/min/m2 |1.5 |1.3 |1.5 |1.2 |1.0 | |(gal/min/ft2) |4889(120) |4481(110) |4481(110) |3463(85) |3056(75) | |___________________|__________|__________|___________|__________|__________| |Puncture | | | | | | |ASTM D 4833-88 | | | | | | |kN (lb) |0.31(70) |0.42(95) |0.58(130) |0.71(160) |0.80(180) | |___________________|__________|__________|___________|__________|__________| |Mullen | | | | | | |Burst | | | | | | |ASTM D 3786-87 | | | | | | |kPa (psi) |1654(240) |2239(325) |2756(400) |3617(525) |4134(600) | |___________________|__________|__________|___________|__________|__________| |Trapezoid | | | | | | |Tear Strength | | | | | | |ASTM D 4533-91 |0.22 |0.27 |0.38 |0.45 |0.51 | |kN (lb) |(50) |(60) |(85) |(100) |(115) | |___________________|__________|__________|___________|__________|__________| |Grab/Tensile | | | | | | |Elongation | | | | | | |ASTM D 4632-91 |0.53 |0.67 |0.89 |1.11 |1.34 | |kN (lb)% |(120)/50 |(150)/50 |(200)/50 |(250)/50 |(300)/50 | |___________________|__________|__________|___________|__________|__________| |Wide With | | | | | | |Tensile Elongation | | | | | | |ASTM D 4595-86 | | | | | | |kN/m (lb/in) | | | | | | |MD |NA |NA |NA |NA |NA | |XD |NA |NA |NA |NA |NA | |___________________|__________|__________|___________|__________|__________| |Manufacturer's | | | | | | |Suggested | | | | | | |Applications |NP |NP |NP |NP |NP | |___________________|__________|__________|___________|__________|__________| S/S = Separation/Stabilization D = Drainage R = Reinforcement P = Protection F = Filtration E = Erosion Control A/O = Asphalt Overlay S/F = Silt Fence O/C = Other or Combination NP = Not provided by manufacturer PP = Polypropylene PET = Polyester PE = Polyethylene
_____________________________________________________ |Property |Mirafi |Mirapave |MFC 1212 | | |1160N |(3) | | |___________________|__________|__________|___________| |Mass Per Unit | | |(typical | |g/m2 (oz/yd2) |NA |NA | values) | |___________________|__________|__________|___________| |Structure |Nonwoven |Nonwoven |Woven | | | | |(coated) | |___________________|__________|__________|___________| |Polymer | | | | |Composition |PP |PP |PE | |___________________|__________|__________|___________| |% Open Area | | | | |CWO-22125 |NA |NA |NA | |___________________|__________|__________|___________| |AOS | | | | |ASTM D4491-87 | | | | |mm (U.S. Seive) |0.149(100)|0.210(70) |NA | |___________________|__________|__________|___________| |Permittivity | | | | |ASTM D4491-92 | | | | |sec-1/Flow Rate | | | | |l/min/m2 |0.7 |NA | NA | |(gal/min/ft2) |2037(50) | | | |___________________|__________|__________|___________| |Puncture | | | | |ASTM D 4833-88 | | | | |kN (lb) |1.07(240) |0.27(60) |0.45(100) | |___________________|__________|__________|___________| |Mullen | | | | |Burst | | | | |ASTM D 3786-87 | | | | |kPa (psi) |5512(800) |1378(200) |2963(430) | |___________________|__________|__________|___________| |Trapezoid | | | | |Tear Strength | | | | |ASTM D 4533-91 |0.65 |0.16 |0.22 x 0.22| |kN (lb) |(145) |(35) |(50 x 50) | |___________________|__________|__________|___________|