__________________________________________________________________________ |Property |Carthage |Carthage |Carthage |Carthage |Carthage | | | 6% |10% |15% |20% |30% | |__________________|__________|__________|___________|__________|__________| |Mass Per Unit | | | | | | |g/m2 (oz/yd2) |NA |NA |NA |NA |NA | |__________________|__________|__________|___________|__________|__________| | |Woven | Woven | Woven |Woven |Woven | |Structure |(calen- |(calen- | | |(palmered)| | | dered) | dered) | | | | |__________________|__________|__________|___________|__________|__________| |Polymer | | | | | | |Composition |PP | PP | PP | PP | PP | |__________________|__________|__________|___________|__________|__________| |% Open Area | | | | | | |CWO-22125 | 5-6% | 10-12% | 12-15% | 15-20% | 25-30% | |__________________|__________|__________|___________|__________|__________| |AOS |0.212 |0.425-.30 |0.425-.30 |0.212 |0.425-.30 | |ASTM D4491-87 |(70) | (40-50) | (40-50) |(70) | (40-50) | |mm (U.S. Seive) | | | | | | |__________________|__________|__________|___________|__________|__________| |Permittivity | | | | | | |ASTM D4491-92 | | | | | | |sec-1/Flow Rate | | | | | | |l/min/m2 |0.29/773 |1.2/3621 |1.5/4678 |0.55/1505 | 2.1/6143 | |(gal/min/ft2) | (19) | (89) | (115) |(37) |(151) | |__________________|__________|__________|___________|__________|__________| |Puncture | | | | | | |ASTM D 4833-88 | | | | | | |kN (lb) |0.664(145)|0.578(130)|0.533(120) |0.667(150)|0.533(120)| |__________________|__________|__________|___________|__________|__________| | | | | |Mullen | | | | | | |Burst | | | | | | |ASTM D 3786-87 | | | | | | |kPa (psi) |3376(490) |3514(510) |3514(510) |4100(595) |2859(415) | |__________________|__________|__________|___________|__________|__________| |Trapezoid | | | |0.467 x | | |Tear Strength |0.449 x |0.356 x |0.511 x | 0.644 |0.422 x | |ASTM D 4533-91 | 0.289 | 0.333 | 0.356 |(105 x | 0.244 | |kN (lb) |(110 x 65)|(80 x 75) |(115 x 80) | 145) |(95 x 55) | |__________________|__________|__________|___________|__________|__________| |Grab/Tensile |1.69 x |1.22 x |1.64 x 0.91|1.24 x |1.47 x | |Elongation | 1.16 | 1.16 | | 1.73 | 0.93 | |ASTM D 4632-91 |(380 x |(275 x |(370 x 205)|(280 x |(330 x | |kN (lb)% | 260)/15 | 260)/16 | /10 | 390)16 | 210)/15 | |__________________|__________|__________|___________|__________|__________| |Wide With | | | | | | |Tensile Elongation| | | | | | |ASTM D 4595-86 | | | | | | |kN/m (lb/in) | | | | | | |MD |32.4 |27.15 |35.9 |32.4 |31.52 | | |(185)/27 |(155)/15 |(205)/19 |(185)/10 |(180)/20 | |XD |26.27 |28.9 |24.52 |32.4 |20.14 | | |(150)/13 |(165)/17 |(140)/8 |(185)/27 |(115)/15 | |__________________|__________|__________|___________|__________|__________| |Manufacturer's |E,F,F,S/F,|E,F,D,S/F,|E,F,D,S/F, |E,F,D,S/F,|E,F,D,S/F,| |Suggested |S/S,R |S/S,R |S/S,R |S/S,R |S/S,R | |Applications | | | | | | |__________________|__________|__________|___________|__________|__________| S/S = Separation/Stabilization D = Drainage R = Reinforcement P = Protection F = Filtration E = Erosion Control A/O = Asphalt Overlay S/F = Silt Fence O/C = Other or CombinationGeotextile Product Data - Carthage Mills CONT
__________________________________________________________________________ |Property |FX-55 |FX-66 |FX-4ONS |FX-6ONS |FX-8ONS | |__________________|__________|__________|___________|__________|__________| |Mass Per Unit | | | | | | |g/m2 (oz/yd2) |NA |NA |NA |NA |NA | |__________________|__________|__________|___________|__________|__________| |Structure |Woven |Woven |Nonwoven |Non-woven |Non-woven | |Structure | | | | | | |__________________|__________|__________|___________|__________|__________| |Polymer |PP |PP |PP |PP |PP | |Composition | | | | | | |__________________|__________|__________|___________|__________|__________| |% Open Area |<1% |3,8,4,5, |NA |NA |NA | |CWO-22125 | | 5.3 | | | | |__________________|__________|__________|___________|__________|__________| |AOS | | | | | | |ASTM D4491-87 |0.425 |<1% |0.212 |0.212 |0.212 | |mm (U.S. Seive) |(40) |(40-50) |(70) |(70) |(70) | |__________________|__________|__________|___________|__________|__________| |Permittivity | | | | | | |ASTM D4491-92 | | | | | | |sec-1/Flow Rate | | | | | | |l/min/m2 |NA |0.425-0.30|2.2/6712 |1.5/4678 |1.1/3661 | |(gal/min/ft2) | | |(115) |(115) |(90) | |__________________|__________|__________|___________|__________|__________| |Puncture | | | | | | |ASTM D 4833-88 | | | | | | |kN (lb) |0.467(105)|NA |0.289(65) |0.422(95) |0.60(135) | |__________________|__________|__________|___________|__________|__________| | | | | |Mullen Burst | | | | | | |ASTM D 3786-87 | | | | | | |kPa (psi) |3169(460) |0.556(125)|1585(230) |2343(340) |3032(440) | |__________________|__________|__________|___________|__________|__________| |Trapezoid | | | | | | |Tear Strength | | | | | | |ASTM D 4533-91 |0.378 |4134(600) | 0.20 |0.311 |0.422 | |kN (lb) |(85) | (120) | (45) |(70) |(95) | |__________________|__________|__________|___________|__________|__________| |Grab/Tensile | | | | | | |Elongation | | | | | | |ASTM D 4632-91 |0.889 |0.533 |0.489 |0.733 |1.0 | |kN (lb)% |(200)/15 |(300)/15 |(100)/50 |(165)/50 |(225)/50 | |__________________|__________|__________|___________|__________|__________| |Wide With | | | | | | |Tensile Elongation| | | | | | |ASTM D 4595-86 | | | | | | |kN/m (lb/in) | | | | | | |MD |21.02 |1.33 |NA |NA |NA | | |(120) |(175) | | | | |XD |21.02 |30.65 |NA |NA |NA | | |(120) |(175) | | | | |__________________|__________|__________|___________|__________|__________| |Manufacturer's |S/S,R |S/S,R |D | D |S/S,D | |Suggested | | | | | | |Applications | | | | | | |__________________|__________|__________|___________|__________|__________| S/S="Separation/Stabilization" D="Drainage" R="Reinforcement" P="Protection" F="Filtration" E="Erosion" Control A/O="Asphalt" Overlay S/F="Silt" Fence O/C="Other" or CombinationGeotextile Product Data - Carthage Mills CONT
__________________________________________________________________________ |Property |FX-38OL |FX-35HS |FX-40HS |FX-60HS |FX-80HS | |__________________|__________|__________|___________|__________|__________| |Mass Per Unit | | | | | | |g/m2 (oz/yd2) |NA |NA |NA |NA |NA | |__________________|__________|__________|___________|__________|__________| | |Nonwoven |Nonwoven |Nonwoven |Nonwoven |Nonwoven | |Structure |(calen- |(heat- |(heat- |(heat- |(heat- | | | dered) | bonded) | bonded) | bonded)| bonded) | |__________________|__________|__________|___________|__________|__________| |Polymer |PP |PP |PP |PP |PP | |Composition | | | | | | |__________________|__________|__________|___________|__________|__________| |% Open Area |NA |NA |NA |NA |NA | |CWO-22125 | | | | | | |__________________|__________|__________|___________|__________|__________| |AOS | | | | | | |ASTM D4491-87 |NA |0.212 |0.212 |0.180 |0.180 | |mm (U.S. Seive) | |(70) |(70) |(80) |(80) | |__________________|__________|__________|___________|__________|__________| |Permittivity | | | | | | |ASTM D4491-92 | | | | | | |sec-1/Flow Rate | | | | | | |l/min/m2 |NA |2.0/6102 |2.0/5695 |1.5/4475 |1.2/3661 | |(gal/min/ft2) | |(150) |(140) |(110) |(90) | |__________________|__________|__________|___________|__________|__________| |Puncture | | | | | | |ASTM D 4833-88 | | | | | | |kN (lb) |0.289(65) |0.244(55) |0.267(60) |0.40(90) |0.511(115)| |__________________|__________|__________|___________|__________|__________| | | | | |Mullen Burst | | | | | | |ASTM D 3786-87 | | | | | | |kPa (psi) |1481(215) |1378(200) |1481(215) |2136(310) |2480(360) | |__________________|__________|__________|___________|__________|__________| |Trapezoid | | | | | | |Tear Strength | | | | | | |ASTM D 4533-91 |0.20 |0.178 | 0.222 |0.289 |0.378 | |kN (lb) |(45) |(40) | (50) |(65) |(85) | |__________________|__________|__________|___________|__________|__________| |Grab/Tensile | | | | | | |Elongation | | | | | | |ASTM D 4632-91 |0.422 |0.422 |0.489 |0.756 |0.978 | |kN (lb)% |(95)/50 |(95)/50 |(110)/50 |(172)/50 |(220)/50 | |__________________|__________|__________|___________|__________|__________| |Wide With | | | | | | |Tensile Elongation| | | | | | |ASTM D 4595-86 | | | | | | |kN/m (lb/in) | | | | | | |MD |NA |NA |NA |NA |NA | |XD |NA |NA |NA |NA |NA | |__________________|__________|__________|___________|__________|__________| |Manufacturer's |A/O |D | D | S/S,D |S/S,D | |Suggested | | | | | | |Applications | | | | | | |__________________|__________|__________|___________|__________|__________| S/S = Separation/Stabilization D = Drainage R = Reinforcement P = Protection F = Filtration E = Erosion Control A/O = Asphalt Overlay S/F = Silt Fence O/C = Other or CombinationGeotextile Product Data - Carthage Mills CONT
___________________________________________________________ |Property |FX-100HS |FX-120HS |FX-120HS | |__________________|_____________|____________|____________| |Mass Per Unit | | | | |g/m2 (oz/yd2) |NA |NA |NA | |__________________|_____________|____________|____________| | |Nonwoven |Nonwoven |Nonwoven | |Structure |(heat-bonded)|(heatbonded)|(heatbonded)| |__________________|_____________|____________|____________| |Polymer |PP |PP |PP | |Composition | | | | |__________________|_____________|____________|____________| |% Open Area |NA |NA |NA | |CWO-22125 | | | | |__________________|_____________|____________|____________| |AOS | | | | |ASTM D4491-87 |0.150 |0.150 |0.150 | |mm (U.S. Seive) |(100) |(100) |(100) | |__________________|_____________|____________|____________| |Permittivity | | | | |ASTM D4491-92 | | | | |sec-1/Flow Rate | | | | |l/min/m2 |1.1/3051 |0.8/2644 |0.6/1831 | |(gal/min/ft2) |(75) |(65) |(45) | |__________________|_____________|____________|____________| |Puncture | | | | |ASTM D 4833-88 | | | | |kN (lb) |0.667(150) |0.756(170) |1.111(250) | |__________________|_____________|____________|____________| |Mullen Burst | | | | |ASTM D 3786-87 | | | | |kPa (psi) |3101(450) |3790(550) |5168(750) | |__________________|_____________|____________|____________| |Trapezoid | | | | |Tear Strength | | | | |ASTM D 4533-91 |0.444 |0.511 |0.733 | |kN (lb) |(100) |(115) |(165) | |__________________|_____________|____________|____________| |Grab/Tensile | | | | |Elongation | | | | |ASTM D 4632-91 |1.267 |1.444 |1.889 | |kN (lb)% |(285)/50 |(325) |(425) | |__________________|_____________|____________|____________| |Wide With | | | | |Tensile Elongation| | | | |ASTM D 4595-86 | | | | |kN/m (lb/in) | | | | |MD |NA |NA |NA | |XD |NA |NA |NA | |__________________|_____________|____________|____________| |Manufacturer's |S/S,P,D | S/S,P |S/S,P | |Suggested | | | | |Applications | | | | |__________________|_____________|____________|____________| S/S = Separation/Stabilization D = Drainage R = Reinforcement P = Protection F = Filtration E = Erosion Control A/O = Asphalt Overlay S/F = Silt Fence O/C = Other or Combination